What is gutter apron?

A gutter apron is a specialized drip edge design meant to direct rainwater directly into the gutter. The apron is normally installed over the roof edge, while folded at about 120 degrees, and hangs into the gutter.

Gutter aprons take on an additional role by hanging down an inch or so into the back of the gutter to prevent water from dripping or splashing behind the gutter. While a drip edge is about 2 1/2 inches wide on both sides of the fold, a gutter apron will usually measure 4 inches or more above and below the fold.

Also Know, whats a gutter apron? A gutter apron is perfect for directing water into your gutters. It installs on the roof edge at the eaves and hangs into the gutter. Used to direct water into the gutter system.

Regarding this, do I need drip edge and gutter apron?

They protect your fascia board from water that could wood rot. In most states, it is not required to have a Drip Edge or a Gutter Apron but it is highly recommended. They are rising in popularity due to it being inexpensive to install and can save a homeowner a lot of money in future repairs.

Can you install gutter apron over drip edge?

A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter. If there’s a drip edge installed where the fascia meets your shingles and the gutter is hung below the drip edge, get some roll flashing and tuck it up under the drip edge and over the top of the gutter.

Should gutters go behind drip edge?

Water Running Behind Your Installed Gutter When the roof shingles do not extend past the metal drip edge the water will suck back on the metal drip edge ( this is called capillary action) and run behind your gutters. Many of the solid gutter covers are design to take advantage of this water characteristic.

Is a gutter apron necessary?

It is highly important to ensure that rainwater flows freely into the gutter. Most roofers and gutter hangers prefer to or rather will recommend the use of gutter aprons for this purpose. Besides protecting the gutter from rot, molding, and damage, the gutter apron also ensures that no water gets behind the gutter.

What does gutter apron look like?

A gutter apron is an L shaped metal and a drip edge is often more like a T shaped metal. Drip edge could work, but the lip is often too short and the shingles often not extended far enough past the fascia due to the T shape, to use the drip edge.

Why is water running behind my gutters?

The most common cause as to why water is dripping behind a gutter system is because there is no drip edge installed. Drip edge is a key component to any roof system. Drip edge is a metal flashing installed under the first row of shingles on a roof slope.

Why does my gutter drip?

If the gutters are clogged, it’s possible that the water is overflowing the gutters and this is contributing to the leak. Water should run out the downspout and away from the house without filling the gutter. If the water fills the inside of the gutter, this means the gutters are clogged.

Does Ice and Water Shield go over the drip edge?

The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Can you install drip edge on existing roof?

Replacing Drip Edge Eave Strips: Install the eave strips on the lower roof edges first, with the eave strips under the shingles and felt underlayment. Align one end of the lower eave strip even with the edge of the roof decking. Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails.

Should you use drip edge touch fascia?

The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.

What size drip edge should I use?

I usually select drip edges with at least a 4-inch roof leg along the eaves edge and a 2-inch leg along rakes. The code calls for the fascia/rake leg to extend 1/4 inch below the roof sheathing and the Fortified Home guides call for 1/2 inch. But I like to use drip edge with at least a 1-inch fascia/rake leg.

What is drip edge?

Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.

How do you install drip edge after shingles?

Make sure the outer edge extends over the gutter. If it doesn’t, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.