What does 5e mean on a Samsung washing machine?

If your Samsung washer is in the middle of a drain cycle and the 5E error code shows on your washers display, it means that the water is not properly draining out of the washer. Something may be clogged, jammed, or blocked and thus preventing water from draining out of the washer.

1-4 of 4 Answers It means “unbalanced and retrying” so it’s going to retry by adding a lot more water.

Likewise, what does 4e means in Samsung washing machine? The 4E (4C) error indicates that the washing machine has detected a problem with the water supply.

Subsequently, one may also ask, what does SE stand for on washing machine?

The SE / 5E error code means that the water draining system has some malfunctions. Samsung washer for some reason can’t cope with water draining and therefore interrupts washing.

What’s wrong with my Samsung washing machine?

Samsung Washer Trips Electrical Circuit There has been a recall on Samsung front load washers because water leakage onto the electrical connections of the washing machine’s thermal sensor can cause an electrical short and ignite the circuit board, posing a fire hazard to consumers.

Where is the drain filter on a Samsung washing machine?

Clogged drain filter Place a shallow pan in front of the filter door at the bottom of the washer to collect water left in the tub. Open the drain pump filter door, pull out the drain tube and remove the drain tube plug. Pull the filter out of the pump and clear any debris from the filter and pump housing.

How do I drain my Samsung washer?

[Solution] 1 Unplug the washing machine from the power supply. 2 Open the filter-cover. 3 Unscrew the emergency drain cap by turning it to the left. 4 Grip the cap on the end of the emergency drain tube, and then slowly pull it out about 15 cm (about 6 inches). 5 Allow all the water to flow into a bowl.

How do I fix my Samsung Washer error?

Unplug the washer and open the door, using force if needed (using force often damages the door lock/switch assembly). Replace the assembly if it’s damaged or defective. The washer fills for 40 minutes or the water level doesn’t change after 6 minutes. Make sure the water supply faucets behind the washer are fully open.

How do I reset my Samsung washing machine?

To reset your Samsung washing machine you need to simply disconnect the washing machine from power for 5 to 10 minutes. (Unplug the washer from the wall outlet or flip the breaker in the breaker box for the washing machine).

What does UE mean on a Samsung washing machine?

Your appliance will display a UE code when it has detected an unbalanced load and has stopped the spin for safety reasons. With any washing machine, it is vital to ensure that the load is evenly balanced when using a spin cycle. Redistribute washing by adding or removing items to ensure a more balanced load.

Where is the MEMS sensor on a Samsung washer?

Answer Aaron, the mems sensor would be accessed by removing the top panel of the washer. The wires can be checked for continuity and repaired as necessary. Answer Carol, the mems sensor is going to be located at the top of the tub assembly near the front.

Why does my Samsung Washer not spin?

To determine if the drive motor is defective, first ensure that the motor is getting power. If the drive motor hums but doesn’t run, is noisy, or does not turn freely, replace it. The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to not spin.

How do I reset my Samsung front load washer?

Push the door closed firmly and press “Power” to turn off the washing machine. Disconnect power to the unit for 10 seconds and then restore power and press “Power” to reset.

How do I fix my Samsung 4e washer?

The first thing to do when you see the NF or 4E error code appear on your Samsung washer: Step 1 – Remove the unit from power! Be sure the water supply valves on the wall behind your washer are fully open. These 2 water valves must be ALL THE WAY open to provide water to your Samsung washer.