Most roofing contractors and roofing companies prefer to or rather will recommend the use of gutter aprons for this purpose. Besides protecting the gutter from rot, molding, and damage, the gutter apron also ensures that no water gets behind the gutter.
They protect your fascia board from water that could wood rot. In most states, it is not required to have a Drip Edge or a Gutter Apron but it is highly recommended. They are rising in popularity due to it being inexpensive to install and can save a homeowner a lot of money in future repairs.
Beside above, what is a gutter apron? A gutter apron is perfect for directing water into your gutters. It installs on the roof edge at the eaves and hangs into the gutter. Used to direct water into the gutter system.
Similarly, which is better drip edge or gutter apron?
Drip Edge Plus Similar to a drip edge, a gutter apron is a long piece of metal folded at about 120 degrees. While a drip edge is about 2 1/2 inches wide on both sides of the fold, a gutter apron will usually measure 4 inches or more above and below the fold. The bottom edge usually has a little fold for rigidity.
Can you install gutter apron over drip edge?
A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter. If there’s a drip edge installed where the fascia meets your shingles and the gutter is hung below the drip edge, get some roll flashing and tuck it up under the drip edge and over the top of the gutter.
Should gutters go behind drip edge?
Water Running Behind Your Installed Gutter When the roof shingles do not extend past the metal drip edge the water will suck back on the metal drip edge ( this is called capillary action) and run behind your gutters. Many of the solid gutter covers are design to take advantage of this water characteristic.
Does drip edge go inside the gutter?
A drip edge is designed to take advantage of those forces and, along with gravity, direct water into the gutter. If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity.
What does a gutter apron look like?
A gutter apron is an L shaped metal and a drip edge is often more like a T shaped metal. Drip edge could work, but the lip is often too short and the shingles often not extended far enough past the fascia due to the T shape, to use the drip edge.
Does Ice and Water Shield go over the drip edge?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Where does gutter apron go?
Gutter apron goes over the roof deck, under the shingles and over the edge of the gutters. Normally used when shingles do not protrude far enuf past the edge of the gutter, or on a low slope, where water could wick back. Water has no where to go except into the gutter.
What is a drip edge gutter apron?
A gutter apron is a specialized drip edge design meant to direct rainwater directly into the gutter. The apron is normally installed over the roof edge, while folded at about 120 degrees, and hangs into the gutter.
Should you use drip edge touch fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.
What is AK style gutter?
The outer shape of the gutter is supposed to (very vaguely) represent the letter K, as opposed to a perfectly-rounded, half-circle-shaped gutter. In other words, the outer edge consists of a short, straight line from the bottom of the gutter, then two opposing curves, followed by another short straight line.
Why is my gutter leaking?
Clogs are one of the most common causes of leaky gutters. Unless you regularly clean them out, your gutters can quickly fill up with leaf litter and debris. Luckily, clogged gutters and downspouts are quite easy to spot. In most cases, you’ll notice the problem as soon as you get a close look in your gutters.
How do I stop water from leaking behind my gutters?
The gutter apron prevents water from ever reaching the soffit by leading water straight into the gutters. To install a gutter apron, slide the apron over the roof deck just beneath the shingles and fit the angled bottom of the apron over the gutters. Then use roofing nails to nail the gutter apron into place.